Clik here to view.
1953 Delta Milwaukee 14" Band Saw Restoration #1: Introduction
I should preface this blog with a note about myself. I recently shed most of my power tools in favor of old hand tools, like Stanley Planes, Disston saws, and old Braces/Bits and eggbeater drills. This...
View ArticleClik here to view.
1953 Delta Milwaukee 14" Band Saw Restoration #2: Lower Wheel Assembly
My package from Iturra arrived this week as planned. One thing I forgot to mention in my previous post as an added benefit of going with Iturra for parts, is that they include instructions on how to...
View ArticleClik here to view.
1953 Delta Milwaukee 14" Band Saw Restoration #3: Lower Wheel Complete and...
I took a vacation day today to get caught up on some chores around the house and work on the band saw for a little while. I had some difficulty removing the “wheel side” bearing from the shaft. I...
View ArticleClik here to view.
1953 Delta Milwaukee 14" Band Saw Restoration #4: Lower Thrust Bearing and...
I had a few spare minutes today so I finished cleaning up the lower thrust bearing and trunnion assembly. I also cleaned up the table and re-installed all of these things. The lower thrust bearing...
View ArticleClik here to view.
1953 Delta Milwaukee 14" Band Saw Restoration #5: Upper Wheel Removal and...
This has been the most difficult thing so far. In reading about other people’s experience, it seems wheels and bearings both upper and lower are hit and miss. My lower wheel wasn’t too much of a...
View ArticleClik here to view.
1953 Delta Milwaukee 14" Band Saw Restoration #6: Finishing Touches
I finished cleaning up the upper guide post and blocks and replaced the upper thrust bearing. This was all pretty simple stuff after doing the others already. I put it all back together and ran it....
View ArticleClik here to view.
Summer Uke Build #1: Getting Ready for Summer (Concert) Uke Build
I have been playing guitar for nearly 30 years and have been woodworking for about 16 years. For a long time, I have wanted to combine these two hobbies by building a guitar or two. About 18 months...
View ArticleClik here to view.
Summer Uke Build #2: Bending the Sides
I took the advice of Bob from his comment on my previous post and soaked the sides overnight. They were still too stiff to bend without tearing out and they did, in fact, tear out some more. So I...
View ArticleClik here to view.
Summer Uke Build #3: Thicknessing, Jointing and Joining the Top
I’m very late with posting this. It was 114 degrees in the shop, so didn’t spend much time taking photos. This all took place on Father’s Day 2016. For the top, I picked up a couple of 6’ planks of...
View ArticleClik here to view.
Summer Uke Build #4: Cleaning up the sides
The real drama in this build so far is in the sides. They split and splintered and were generally a bit of a disaster when attempting to bend. The two biggest factors in this were that 1.) I used...
View ArticleClik here to view.
Summer Uke Build #5: Joining Back, Gluing Neck Block, Adding Rosette
In the last few weeks I’ve managed to steal a few hours to work on the uke and make a little progress. The weather is cooling a bit so that makes it easier to be in the garage for longer periods of...
View ArticleClik here to view.
Summer Uke Build #6: Cutting Soundhole Making Radius Dishes
Today’s update is a bit incomplete. I cut out the soundhole and sanded down the olive wood rosette to be a little more level with the top. I bought a drum sander in the interim as I just don’t trust...
View ArticleClik here to view.
Summer Uke Build #7: Tail detail/Kerfed Lining/Top Braces
I haven’t posted in quite some time, but haven’t had time to do much in the last few months. I have managed to get some shop time the last two weeks. I was prepared to abandon the project, at least for...
View ArticleClik here to view.
Summer Uke Build #8: Gluing Top Bracing, Roughing Back Braces
Another vacation day today and so another day in the shop. Today I made a bridge plate. The only stock I had on hand that was already thin enough and hard enough to do the job was some cut-off wood...
View ArticleClik here to view.
Summer Uke Build #9: Not summer anymore but still a uke build
So summer has become winter and I’m still not even close to finished with this. But I nibble away at it when I can. I had a couple of vacation days late last week that were intercepted by a sick...
View ArticleClik here to view.
Summer Uke Build #10: Gluing the back... or not.
Last night I picked up a bunch of #64 rubber bands from Office Max and decided to use them to glue the back on the uke. The back was radiused using the radius dish I made, so I thought I’d screw some...
View ArticleClik here to view.
Summer Uke Build #11: Glue the back / go-bar deck
Update from yesterday’s post #10The shelf lining that I used on the top sheet of plywood in the go-bar deck came loose overnight. There seems to be some kind of chemical reaction between the 3M spray...
View ArticleClik here to view.
Summer Uke Build #12: The body is complete (except maybe binding)
I pulled the go-bars off this morning. Using a chisel, I trimmed the excess wood from the back to be flush with the sides. It turned out pretty well. There’s a nice radius to the back and the seam...
View ArticleClik here to view.
Summer Uke Build #13: Neck Scarf Joint
Today I was able to get the scarf joint for the neck done and I went to Rockler to see if they had any wood that would make a good fingerboard. I had a $5 off coupon and got a $6 piece of mahogany, but...
View ArticleClik here to view.
Summer Uke Build #14: Fingerboard Blank
I’ve been trying to figure out how to get a fingerboard blank. I have been reading up on woods that are appropriate for the purpose and only very hard woods will work. Ebony is most common with...
View Article